How Will I Know If My Car Needs Repair Or Replacement?

Are you confused if you need a car repair or a car replacement? Well, it is best that youre confused because it only means that you are sensible about the right choices in your life. You may want to consider some tips to lead you to the right decision. It is sometimes hard to choose between car repair and car replacement.

Some car owners will say that their car has a sentimental value or others say that theirs have a better mileage. Well, that might be true, however, its not wise to have a regular visit to an auto shop every once a month. I will give you some tips and factors that will surely make your decision easy. First, think about money savings. If you are bringing your car in the auto shop every month, it may not be healthy to your pocket. You may pay the same amount every month by getting a brand new car at no hassle. So, you have to compare the monthly cost of getting a new car and the monthly cost of your regular car check ups and repairs of your current car. Second, think about the risk of your life. An outlook of your future car maintenance may be clear.

If you think that your car needs an expensive maintenance in the future, then you have to do the decision right. And another factor is the risk that will lead you on the road, it may not be safe to drive on your car anymore if some parts are reassembled or other factors will cover also. And if your future car maintenance is higher or even just the same by getting a new car, then the situation is giving you a clear suggestion what to do. Third factor to consider is about the cost of your future car if you would consider getting one. The amount of your future car is a big factor that you have to consider and the way how would you pay for it. Now, on this factor, you have to consider your annual car repair cost, the estimated monthly payment of a target car, and the value of your current car. The trick here is, if you pay more money as a down payment, you most likely have to have a cheaper monthly rate. So if your current car can pay a big amount for the down payment, and your current monthly maintenance cost is a lot higher, you may want to consider a good and easy choice then. The last factor is the cost of your current car. This factor will affect if you want to have your car traded to a new car. This is the most common practice of a car owner. It may take some time to look for a dealer or a car seller but this may yield money and just adding a little amount for getting a new one. There are a lot of car traders that you can deal with. You can compare their offers and choose the best offer possible. By practicing this simple guides and tips, you now can decide if you want a car repair or a car replacement. These tips will give you an undoubtedly wise decision.Some Related Articles

Photo Steps: replacing rear axles

The following sequence of photo-graphs shows the step-by-step procedure for removing an axle from a car which uses a C-type axle lock to hold the rear axles in place. The C-type lock is discussed later in this chapter.

1 Place a drain pan under the differ-ential housing and, using the correct size socket wrench, remove two or three lower bolts and one upper bolt to allow the rear end grease to spill out of the housing.

2 Remove the remaining bolts and the cover. If the cover is stuck to the housing, use a screwdriver to pry it free.

3 Use a scraper to remove the old gasket from both the cover and the axle housing.

4 Turning the drive shaft with one hand, rotate the rear end slowly until the lock bolt pin is just at the bottom of the rear end housing. Now loosen the lock bolt with a box or Allen wrench.

5 Remove the lock pin.

6 Slide the pinion shaft pin out just until it clears the end of the axle. Do not remove the pin.

7 Have a helper push in on the axle flange until the C lock is exposed.

8 Using long-nose pliers, remove the C lock from the axle.

9 Have a helper pull the axle out and remove it. Then push the pinion shaft pin back into place and loosely install the lock pin.

10 Using a slide hammer seal-re-moving tool, take out the axle bearing and/or seal.

11 Using a seal-installing tool and a hammer, install the new seal in the axle housing. Now have your helper install the axle. Once again, remove the lock pin, slide the pinion shaft out far enough to allow the axle to shdo into place, and install the C lock on the axle. With the C lock in place, have your helper pull out on the axle until it sets in place. Again slide the pinion shaft pin into the case and tighten the lock bolt securely.

12 Coat the differential housing cover with gasket cement.

13 Install a new gasket on the differ-ential cover, and put the cover on the housing. First start all cover bolts by hand, then tighten them using the tight-ening sequence described later in this chapter.

14 Fill the differential assembly with rear end grease.